Ghost Immobiliser Fitting
Protect your vehicle against key theft, cloning, and hacking by using the first aftermarket CAN-Immobiliser. The Ghost app and GPS tracking can be linked to the immobiliser to give you notifications when your vehicle is taken or damaged.
The installation of the Ghost immobiliser is done by a qualified technician. It is important to have the right tools and heat shrink tubing.
Getting Started
Ghost immobilisers are an excellent alternative to physical theft protection devices like car alarms and wheel locks. They guard your vehicle without using LED indicators or key fobs. They are directly connected to the ECU CAN data network and can only be activated after entering a PIN code. This gives a more secure level of protection from key hacking, cloning and even ECU swapping.
As a result, installing a ghost immobilise r Birmingham must be completed with great speed and accuracy. It's like walking through a minefield. A single mistake could cause serious damage to your vehicle's circuits. To avoid this, it's crucial that you know the procedure for installing and prepare your vehicle appropriately.
First, you must prepare the vehicle by removing the interior panels to make room for the immobiliser device. Once you have found the perfect location to conceal it, use cable tie to secure it. Then, clean up the wiring by tying down loose wires, and then using insulation tape or heat shrink tubing to cover the exposed connections. This will reduce the chance of short circuits that are not intended to be there as well as improving aesthetics and reducing the likelihood of tampering by thieves.
Then, locate a source of constant 12V power as well as a grounding location for the ghost immobiliser. Once you've located these and tested the power wires with a multimeter to make sure they are delivering a consistent voltage. Connect the CAN H & the CAN L wires from the immobiliser with the power source and grounding points.
It's important that you double-check all the connections and examine the immobiliser for indications of corrosion. By entering a PIN and then starting the car is a good way to test the system. This should become a part of your routine since it allows you to identify any issues that may arise early. Regular testing will also help to extend the life of the device, and ensure that it is running at its peak performance.
Preparing your vehicle
The installation of an Ghost immobiliser is a complex job that requires the appropriate tools and knowledge. A wiring diagram is essential for finding the correct wires, making accurate connections, and ensuring safety. A multimeter is a tool to test electrical values and ensure security. Insulation tape and cable tie can be used to secure the connections and protect them from tampering. A user's manual is available for your Ghost Immobiliser. It will give you specific instructions that are tailored to your model.
Once installed, a ghost immobiliser can prevent unauthorised engine start by requiring the owner to enter a unique PIN sequence through existing buttons in the steering wheel or center console. This can be accomplished manually or remotely through the mobile phone app and the code can easily be changed by the vehicle owner at anytime. The device is also silent and is undetectable by thieves as it does not emit any radio frequencies.
A ghost immobiliser connects directly to the vehicle's CAN bus, which is a network that connects to all the vehicle's electronic control units (ECUs). It intercepts signals from the ECUs and prevents the engine from starting if a false signal is detected. The system is weatherproof and tamper proof. It has no keys or LED indicators to draw thieves' attention.
It can be placed behind the dashboard or in a discreet area, so that it is not visible to thieves and does not hinder the performance of the vehicle. It can be tucked away in a small container so that it is less likely to be spotted by unscrupulous salespeople during a test-drive.
Its discrete operation and integration with the vehicle's CAN bus system makes it a powerful deterrent to modern methods of car theft, including key cloning and signal relay attacks. The system can be combined with other security measures to create a powerful barrier that can deter even the most persistent thieves. This is why more insurance companies are advocating or even requiring ghost immobilisers to be installed, since it will significantly lower the cost of insurance.
Making the Connections
Contrary to traditional security systems which are heard by thieves ghost immobilisers operate in a quiet manner to stop them from knowing that your vehicle is turned on. They also prevent high-tech methods of stealing vehicles, like OBD hacking. Installing them without leaving permanent marks on your car is an excellent alternative for those planning to sell their vehicle in the near future.
The Autowatch Ghost 2 is a immobiliser for CANbus that is one of the most reliable and modern solutions to stop car theft. It makes use of the CAN data network to deactivate your engine and generates a PIN code that only you know, so it is difficult for thieves to identify. It can be installed in various vehicles and is compatible with a variety of available features, including car alarms, GPS trackers, steering wheel locks, and door lock bypass systems.
If you decide to go with an Ghost immobiliser, be sure to consult the wiring diagram for your specific vehicle model to identify the wires to connect. Double-check their locations to ensure they are exact, and label them or tape them to help keep track of them. You'll also need to locate a source of constant power (12V) and a grounding point to the system. Once you have all the components, you can start making connections to complete the installation.
When the ghost immobiliser is connected to the CAN bus, it will block your vehicle from starting unless you enter a pin code through the buttons on the dashboard or steering wheel. This will stop ECU replication and other methods of stealing vehicles. It can also be used with other Thatcham approved security devices such as alarms and tyre clips to give your vehicle an even higher degree of security.
As the UK automotive aftermarket market expands, so are the options for securing your vehicle. With so many avenues for thieves to break in and steal your vehicle it's crucial to take every precaution to prevent it from being taken away. Ghost immobilisers are a popular option among car owners who are accountable.
Testing the System
The Ghost Immobiliser communicates with the vehicle's ECU via a CAN network. This stops the engine from being started until a PIN code has been entered. This makes it very difficult for thieves to copy your key fob to open your vehicle, and more difficult to disable the system by hacking its electronics.
Ghost Immobilisers can also be used in conjunction with GPS tracking devices to help you locate your vehicle if it's stolen. This feature isn't often found in aftermarket security products however it's an excellent way to improve the security of your vehicle and give you peace of mind.
In addition to providing increased security, in addition to providing enhanced security, the Ghost-II immobiliser offers a convenient user experience by eliminating the need for additional key fobs and devices. It has a simple, user-friendly PIN code entry system that works seamlessly into your daily routine. It also offers deactivation modes and convenience features that let you temporarily disable the immobiliser for valet parking or servicing.
Before you begin the installation process, familiarise yourself with your vehicle's wiring and prepare the required tools. A basic set will allow you to make precise connections. A multimeter can be used to check electrical values. Insulation tape and heat shrink tubing are also crucial for securing connections from short circuits while cable tie is a great way to hold the wire in place. It is also essential to be in a well-lit space and wear the appropriate safety equipment when working with tools and electrical components.
After you've completed the installation you should test the Ghost immobiliser to verify that it's working properly. Try to start the car without entering the PIN. If this doesn't work, you'll need to test the system again and perform a more thorough inspection of the connections.
In contrast to other security systems, unlike other security systems, the Ghost Immobiliser is a covert device that cannot be detected by thieves and is more effective than conventional physical deterrents like wheel clamps or steering locks. It is TASSA-approved and recognized by some insurance companies. This makes it a cost-effective investment that gives you the peace of mind you deserve.